KitchenAid Dishwasher F7E2 Code: Wash Motor Error or Heater Stuck On
F7E2 appears as a wash motor error (reset by power cycle) and as a heater drive circuit fault in service tables.
Model compatibility: KitchenAid reuses codes across series and model years, so F7E2 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.
What this code means
Wash Motor Error in owner help, with a power cycle; heater stuck on, a heater drive circuit fault on the control, in service tables.
Look up F7E2 in KitchenAid’s material and two different descriptions turn up. Whether you meet one or the other depends on which document you open, and KitchenAid gives no model split.
At a glance
| Code | F7E2 |
|---|---|
| What it means | Either a wash motor error or a heater stuck on because of a heater drive circuit fault on the control. |
| What you can check | Cycle the power for a full 30 seconds: unplug the dishwasher and plug it back in, or switch the breaker off at the household panel and back on after the same wait. |
| When to call a technician | If the code comes back after the reset, schedule service. If a heater might be stuck on, keep the door closed and the dishwasher unplugged until the technician arrives. |
| Document | Label | Advice |
|---|---|---|
| Owner help | Wash Motor Error | Cycle the power, then schedule service if the code returns |
| Service tech sheet and job aid | Heating, heater stuck on | Heater drive circuit on the control is faulty; owners have no steps |
Steps for the reset
Think of it as restarting a computer, which is the comparison KitchenAid makes. Remove power for a full 30 seconds. With a plug, disconnect it and reinsert it after the wait. If the machine is wired in, turn the breaker off at the household panel, count the same 30 seconds and turn it on.
After the reset
Service follows in both cases if the code persists. Owner help says so directly. In the tech sheet the fault is on the control, out of reach for an owner.
About a heater that is stuck on
A stuck-on heater, in general terms, stays powered when the control asks for it to stop. The service line points to the heater’s drive circuit on the control; it makes no claim about the heating element. Keep the machine closed, unplug it and wait for the technician.
Compare with these entries
- F7E1 lists no heat, the reverse of stuck on.
- F4E4 is wash motor failure in the service tables.
- F4E3 is a heating error from the owner pages.
KitchenAid dishwasher repair for F7E2 in metro areas
Across the Miami, New York, Houston, Los Angeles and San Diego metro areas, (844) 919-2035 is the number for a KitchenAid dishwasher with F7E2. Let us know the 30-second power cycle was tried, and have the model number. The dishwasher repair page is linked here.
Source: KitchenAid Product Help, Dishwasher Error Code or Flashing Lights; KitchenAid Product Help, Dishwasher Error Codes – Reading; KitchenAid Tech Sheet W10750900 Rev C; KitchenAid Job Aid W10573282
Important safety warning. Do not attempt repairs involving electrical components, gas, water lines, refrigerant or sealed systems. Unplug the appliance if it is safe to reach the outlet, and leave internal diagnostics to a qualified technician.
Sources & references
- KitchenAid Product Help - Dishwasher: Error Code or Flashing Lights
- KitchenAid Product Help - Dishwasher Error Codes - Reading
- KitchenAid Tech Sheet W10750900 Rev C (dishwasher, 'FOR SERVICE TECHNICIAN'S USE ONLY'): Service Error Codes table
- KitchenAid Job Aid W10573282: 2013 Stainless Steel Tall Tub Dishwasher, Section 5 Service Error Codes
Tell us what’s wrong — we’ll take it from there
Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.
Request your repair
Fields marked with * are required.