KitchenAid KDFE454 Built-in Dishwasher
Built-in dishwasher where dishes stay wet, cycles quit early or the door latch throws a fault code.
Model overview
A 15-place-setting capacity in its CSS configuration makes the KitchenAid KDFE454 a built-in dishwasher for a busy kitchen. ProScrub directs 36 targeted spray jets at the dishes, while ProWash changes the wash to suit the load. The upper rack runs on SatinGlide rails with height adjusters, the lower-rack tines fold down for tall items, and Heat Dry uses a recessed heating element. The wash tub is stainless steel. The unit requires 120 V, 60 Hz AC on a 15- or 20-amp fused supply, so the circuit should be checked first. For the booking form, state the complete model number from the rating label, the cycle that fails to clean or dry, and any door or leak code on the display.
At a glance
| Model | KDFE454 |
|---|---|
| Appliance | 24-inch built-in dishwasher |
| Common symptoms | dishes not getting clean or dry; door latch or control panel problems; cycle stops early or will not start; leak or leak-protection code |
| What you can check | Note the cycle used, whether water is left in the tub, and any code or flashing light. |
| When to call a technician | If the symptom comes back after the simple checks, or you see a code, leaking water or a burning smell, book a visit. |
Specifications
| Capacity | The CSS configuration holds 15 place settings. |
|---|---|
| Power | Requires 120 V, 60 Hz AC power on a 15- or 20-amp fused supply. |
| Features | ProScrub uses 36 targeted spray jets. ProWash automatically adjusts the wash cycle. The upper rack has SatinGlide rails and height adjusters. Lower-rack tines fold down to accommodate larger items. Heat Dry activates a recessed heating element. |
| Finish | The wash tub is stainless steel. |
What sets the KDFE454 apart
Built-in dishwashers of this kind differ more in spray design and rack setup than in outward shape. This model relies on ProScrub jets, and its upper rack adjusts on SatinGlide rails while the lower tines fold for pots. Heat Dry depends on the recessed element doing the drying, so there is no separate vent to inspect. The owner can load taller cookware low and set the upper rack height without changing the wash path.
Service notes for the KDFE454
When dishes come out dirty or wet, a technician starts at the spray arms, the filter and the drain rather than at the control board. Food debris blocks the 36 ProScrub jets, so clearing them is the first step once the filter sits correctly. A door latch or panel fault usually comes from a worn latch or a loose connector behind the door liner. Leak codes trace to the inlet valve or the drain hose. Before the visit, the owner can note the cycle name, whether Heat Dry was selected and the exact code on the display. Disconnect power before opening the lower panel.
The model number is printed on the rating label, usually on the edge of the door or the side of the tub, visible when the door is open; match it letter for letter before booking, because a single letter can change parts.
Common issues for this model
- Dishes not getting clean or dry
- Door latch or control panel problems
- Cycle stops early or will not start
- Leak or leak-protection code
Related error codes
KitchenAid Dishwasher F6E8 Code: Water Softener Regen Valve
F6E8 concerns the electrical side of the softener regen valve, on water softener models only.
KitchenAid Dishwasher FAE4 / F10E4 Code: Diverter Valve Error
FAE4 and F10E4 are the same KitchenAid entry: a diverter valve error, cleared first by cycling power.
KitchenAid Dishwasher F9E3 Code: Diverter Disk Missing
F9E3 is a short service entry: the diverter disk in the sump has gone missing.
KitchenAid Dishwasher F8E5 Code: Stuck Open Fill Valve
F8E5 points to a fill valve stuck open. KitchenAid's listed steps stop the water and handle the alarm.
Recommended repair service
Dishwasher Repair
Dishwasher not draining, not cleaning, or showing an error code? We find the cause and get your KitchenAid dishwasher back to spotless cycles.
Troubleshooting resources
Note the cycle used, whether water is left in the tub, and any code or flashing light.
Model-information disclaimer. Confirm your exact model number and specifications with your appliance documentation before booking a repair. Model pages are for identification and compatibility reference.
Frequently asked questions
The CSS configuration is rated for 15 place settings.
It requires 120 V, 60 Hz AC power on a 15- or 20-amp fused supply.
Check the rating label on the edge of the door or the side of the tub, visible when the door is open. Copy every letter and digit, including the ones at the end.
Yes. We book in-home visits for this model in the Miami, New York, Houston, Los Angeles and San Diego metro areas. Add the model number and the symptom to the booking form.
Tell us what’s wrong — we’ll take it from there
Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.
Request your repair
Fields marked with * are required.