KitchenAid Dishwasher F6E1 Code: Control Error or Inlet Water
F6E1 is read two ways by KitchenAid: a main control error cleared by power cycling, or a low or no inlet water problem in service tables.
Model compatibility: KitchenAid reuses codes across series and model years, so F6E1 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.
What this code means
F6E1 is listed as a User Interface Error, Main Control in owner help and as low or no inlet water in the service tables.
Depending on which KitchenAid document you open, F6E1 means something different. That is worth knowing before you act on the code.
At a glance
| Code | F6E1 |
|---|---|
| What it means | F6E1 means a control or user interface error, or low or no water coming into the dishwasher. |
| What you can check | Unplug the dishwasher for 30 seconds, or switch its breaker off for 30 seconds if it is hard wired, then restore power. See whether F6E1 returns. |
| When to call a technician | If F6E1 is still there after the reset, schedule service under either meaning of the code. Say that you cycled power and whether the dishwasher was filling. |
- Owner help: the potential cause is a control problem, a user interface error.
- Technician service tables: low or no water at the inlet.
First, the power cycle
Troubleshooting in the owner help is a single line: cycle power, and call for service if the error code is still there. KitchenAid compares it to a computer restart, with the control disconnected for 30 seconds.
- If the dishwasher plugs into an outlet, unplug it, wait 30 seconds and plug it in.
- If it is hard wired, switch the breaker off at the home panel, wait 30 seconds and switch it on.
What the tech documents say
Here F6E1 is described as a mechanical problem with the water coming in, and the list has four entries: no supply of water, captured wash water, a problem in the drain loop, and an issue with the fill valve or line. There are no owner steps, because the audience works on the opened machine.
Deciding between the two
No document says which models follow which reading, so the code alone cannot tell you. The practical route is to do the power cycle and see if F6E1 is back. A returning code means service under either reading. Mention what the dishwasher was doing when it appeared, above all whether it was filling.
Related KitchenAid dishwasher codes
- F6E2: electrical fill valve
- F1E2: main control communication error, with its own reset listing
- H2O: not detecting water, which includes supply checks
Dishwasher service for control and water problems
If the reset does not hold, call (844) 919-2035 for KitchenAid dishwasher service in the Miami, New York, Houston, Los Angeles and San Diego metro areas. Say that you cycled power and give the model number.
Source: KitchenAid Product Help, Dishwasher Error Code or Flashing Lights; KitchenAid Product Help, Dishwasher Error Codes – Reading; KitchenAid Tech Sheet W10750900 Rev C; KitchenAid Job Aid W10573282
Important safety warning. Do not attempt repairs involving electrical components, gas, water lines, refrigerant or sealed systems. Unplug the appliance if it is safe to reach the outlet, and leave internal diagnostics to a qualified technician.
Sources & references
- KitchenAid Product Help - Dishwasher: Error Code or Flashing Lights
- KitchenAid Product Help - Dishwasher Error Codes - Reading
- KitchenAid Tech Sheet W10750900 Rev C (dishwasher, 'FOR SERVICE TECHNICIAN'S USE ONLY'): Service Error Codes table
- KitchenAid Job Aid W10573282: 2013 Stainless Steel Tall Tub Dishwasher, Section 5 Service Error Codes
Tell us what’s wrong — we’ll take it from there
Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.
Request your repair
Fields marked with * are required.