KitchenAid KDTE404 Built-in Dishwasher
Top-control built-in dishwasher where dishes stay cloudy, a cycle stops or a leak code appears after loading.
Model overview
Controls on the top of the door and a 24-inch required cutout set the KitchenAid KDTE404 apart as a built-in dishwasher. The stainless tub carries the ProScrub Trio wash option, and ProWash adjusts the cycle to both the size of the load and its soil level. The manual calls for rinse aid to dry dishes well, so a wet load is often a rinse aid question before it is a mechanical one. The unit needs 120 V, 60 Hz power on a 15- or 20-amp fuse. Homeowners across the metro areas we cover should check the rinse aid dispenser before scheduling a visit. In the booking form, include the complete rating-label number, the cycle that stops or the dishes that leave wet, and any leak code.
At a glance
| Model | KDTE404 |
|---|---|
| Appliance | 24-inch built-in dishwasher |
| Common symptoms | cycle stops early or will not start; dishes not getting clean or dry; leak or leak-protection code; door latch or control panel problems |
| What you can check | Note the cycle used, whether water is left in the tub, and any code or flashing light. |
| When to call a technician | If the symptom comes back after the simple checks, or you see a code, leaking water or a burning smell, book a visit. |
Specifications
| Dimensions | Required cutout width is 24 inches. |
|---|---|
| Power | Requires a 120 V, 60 Hz supply with a 15- or 20-amp fuse. |
| Features | Includes the ProScrub Trio option. The ProWash cycle adjusts washing according to load size and soil. |
| Controls | Controls are on the top of the door. Press Start/Resume after opening the door during a cycle. |
| Care | The manual specifies rinse aid for good drying performance. |
| Finish | The wash tub is stainless steel. |
What sets the KDTE404 apart
Controls on the door top sit where the owner reaches for them first, and the ProScrub Trio option adds a wash choice beyond the standard cycles. ProWash changes its run time with the load, so the cycle length varies. After opening the door mid-run, pressing Start/Resume continues the cycle rather than restarting it.
Service notes for the KDTE404
Cloudy or wet dishes send a technician first to the rinse aid level, the spray arms and the filter, before the heating or drying parts are considered. The owner can top up the rinse aid, clear the filter and check the spray arms for debris. A cycle that pauses after the door opens is normal until Start/Resume is pressed, so that step comes first. Leak codes usually start at the drain hose, the inlet valve or the tub seal, and a puddle along the door edge is a clue. A worn door latch can also halt a run, so the owner should confirm the door closes fully. Disconnect power before opening the lower panel.
The model number is printed on the rating label, usually on the edge of the door or the side of the tub, visible when the door is open; match it letter for letter before booking, because a single letter can change parts.
Common issues for this model
- Cycle stops early or will not start
- Dishes not getting clean or dry
- Leak or leak-protection code
- Door latch or control panel problems
Related error codes
KitchenAid Dishwasher F2E2 Code: Main Control Communication Error
F2E2 means a main control communication error to KitchenAid. A 30-second power-off is the owner step; service follows if it returns.
KitchenAid Dishwasher F3E1 Code: Thermistor Circuit Open
F3E1: KitchenAid's service documents call it an open thermistor/OWI sensor circuit. Three causes are listed and no owner fix is given.
KitchenAid Dishwasher F9E2 Code: Drain Motor Error or Diverter
F9E2 is a drain motor error with a short check list; service tables call it diverter stuck on.
KitchenAid Dishwasher F6E6 Code: Cool Inlet Water
F6E6 reports inlet water under 65F (18C). The job aid names the hot supply connection and the sensing circuit.
Recommended repair service
Dishwasher Repair
Dishwasher not draining, not cleaning, or showing an error code? We find the cause and get your KitchenAid dishwasher back to spotless cycles.
Troubleshooting resources
Note the cycle used, whether water is left in the tub, and any code or flashing light.
Model-information disclaimer. Confirm your exact model number and specifications with your appliance documentation before booking a repair. Model pages are for identification and compatibility reference.
Frequently asked questions
It needs 120 V, 60 Hz on a 15- or 20-amp fuse.
ProWash adjusts washing according to load size and soil.
Check the rating label on the edge of the door or the side of the tub, visible when the door is open. Copy every letter and digit, including the ones at the end.
Yes. We book in-home visits for this model in the Miami, New York, Houston, Los Angeles and San Diego metro areas. Add the model number and the symptom to the booking form.
Tell us what’s wrong — we’ll take it from there
Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.
Request your repair
Fields marked with * are required.