KitchenAid KUDI22OT Built-in Dishwasher
Built-in dishwasher owners ask about water left in the tub, cloudy dishes and doors that will not latch.
Model overview
The KitchenAid KUDI22OT is a built-in dishwasher that runs on 115 V, 60 Hz power and needs incoming water of at least 120°F, or 49°C, to clean well. Its lower wash uses a four-way Hydro Sweep arm with jet spray, and Quiet Scrub insulation keeps operating sound down while a Flo-Thru fan handles drying. Across the metro areas we cover, owners who find water left in the tub or dishes that come out wet should check the water temperature and the rinse agent first. For the booking form, add the symptom, the full model number from the rating label and any code the panel displays.
At a glance
| Model | KUDI22OT |
|---|---|
| Appliance | built-in dishwasher |
| Common symptoms | water left in the tub after the cycle; door latch or control panel problems; dishes not getting clean or dry; cycle stops early or will not start |
| What you can check | Note the cycle used, whether water is left in the tub, and any code or flashing light. |
| When to call a technician | If the symptom comes back after the simple checks, or you see a code, leaking water or a burning smell, book a visit. |
Specifications
| Capacity | The rinse-agent reservoir holds 7 fluid ounces. |
|---|---|
| Power | The dishwasher operates on 115-volt, 60-Hz AC power. |
| Installation | Incoming water should be at least 120°F (49°C). |
| Features | The lower wash system uses a four-way Hydro Sweep arm with jet spray. An overflow-protection float monitors the water level. Flo-Thru drying includes a fan. Quiet Scrub insulation reduces operating sound. |
| Finish | The interior has a porcelain enamel finish. |
What sets the KUDI22OT apart
The Quiet Scrub insulation and the Flo-Thru drying fan set the KUDI22OT apart from a dishwasher that dries by heat alone. Quiet Scrub reduces operating sound, which matters in an open kitchen. The overflow float watches the water level for protection, and the porcelain enamel interior is the surface the owner cleans and inspects most. The rinse-agent reservoir holds 7 fluid ounces, enough to plan refills around a regular schedule.
Service notes for the KUDI22OT
A dishwasher that leaves water in the tub after a finished cycle usually sends a technician to the drain pump, the drain hose and the filter path. The overflow float is one of the first parts checked when the water level seems wrong. The owner can safely check the water temperature at the nearest sink, since the unit needs at least 120°F incoming, and the rinse-agent level in its reservoir. Dishes that come out cloudy or wet are often a rinse-agent or drying-fan question, so the fan and the reservoir should be checked together. A door that sticks or a control panel that does not respond is a separate line of inquiry, so note which happens first. Record the cycle, the symptom and any leak code before calling.
The model number is printed on the rating label, usually on the edge of the door or the side of the tub, visible when the door is open; match it letter for letter before booking, because a single letter can change parts.
Common issues for this model
- Water left in the tub after the cycle
- Door latch or control panel problems
- Dishes not getting clean or dry
- Cycle stops early or will not start
Related error codes
KitchenAid Dishwasher Code F10E2 / FAE2: Vent Wax Motor
Some KitchenAid dishwashers only: F10E2 / FAE2 flags the vent wax motor circuit. No owner steps, so service comes next.
KitchenAid Dishwasher Code F1E2: Control Communication
F1E2 has two descriptions from KitchenAid. A 30-second power cycle is the owner step; a returning code means service.
KitchenAid Dishwasher F3E1 Code: Thermistor Circuit Open
F3E1: KitchenAid's service documents call it an open thermistor/OWI sensor circuit. Three causes are listed and no owner fix is given.
KitchenAid Dishwasher F4E4 Code: Wash Motor Failure
F4E4 means wash motor failure to KitchenAid. Five listed causes cover wiring, circuit, fuse, drive circuit and the motor, with no owner fix.
Recommended repair service
Dishwasher Repair
Dishwasher not draining, not cleaning, or showing an error code? We find the cause and get your KitchenAid dishwasher back to spotless cycles.
Troubleshooting resources
Note the cycle used, whether water is left in the tub, and any code or flashing light.
Model-information disclaimer. Confirm your exact model number and specifications with your appliance documentation before booking a repair. Model pages are for identification and compatibility reference.
Frequently asked questions
Incoming water should be at least 120°F, which is 49°C, so a cold tap can weaken cleaning results.
The reservoir holds 7 fluid ounces, and the owner should top it up before the next full load.
Check the rating label on the edge of the door or the side of the tub, visible when the door is open. Copy every letter and digit, including the ones at the end.
Yes. We book in-home visits for this model in the Miami, New York, Houston, Los Angeles and San Diego metro areas. Add the model number and the symptom to the booking form.
Tell us what’s wrong — we’ll take it from there
Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.
Request your repair
Fields marked with * are required.