KitchenAid KDFE104DSS Built-in Dishwasher
Built-in dishwasher with six cycles and a front console; leaks, standing water and early cycle stops are typical calls.
Model overview
The KitchenAid KDFE104DSS is a built-in dishwasher with a front control console, six wash cycles and a pocket handle. Overall width is 23 7/8 inches, and it runs on 120 V, 60 Hz AC power through a 15- or 20-amp fused supply. ProWash adjusts the wash to the load, and Heat Dry uses a recessed heating element for drying. Lower-rack tines fold down for larger dishes, and a four-hour delayed start is available. Across the metro areas we cover, a leak code or a cycle that stops early are common reasons to call. When you book, describe the symptom, copy the full KDFE104DSS number from the rating label, and note any error code on the console.
At a glance
| Model | KDFE104DSS |
|---|---|
| Appliance | 24-inch built-in dishwasher |
| Common symptoms | water left in the tub after the cycle; leak or leak-protection code; cycle stops early or will not start; dishes not getting clean or dry |
| What you can check | Note the cycle used, whether water is left in the tub, and any code or flashing light. |
| When to call a technician | If the symptom comes back after the simple checks, or you see a code, leaking water or a burning smell, book a visit. |
Specifications
| Dimensions | Overall width is 23 7/8 inches. |
|---|---|
| Power | Requires 120 V, 60 Hz AC power on a 15- or 20-amp fused supply. |
| Features | ProWash adjusts washing in response to the load. Heat Dry activates a recessed heating element. Lower-rack tines fold down for larger dishes. |
| Controls | Six wash cycles are available. A four-hour delayed start is available. |
| Finish | The inner tub and lower wash arms are stainless steel. |
What sets the KDFE104DSS apart
This model keeps its controls on a front console with a pocket handle, and it offers six cycles plus five wash options. ProWash adjusts the wash to the load, so the cycle that runs can differ from the one you picked when the racks are very full. The inner tub and lower wash arms are stainless steel, which is the first place to look after standing water or spotting on glassware.
Service notes for the KDFE104DSS
Water left in the tub after a cycle usually points a technician to the drain path and the drain pump, so the filter at the bottom of the tub is checked first. A leak or leak-protection code leads to the float, the leak sensor and the hose connections, which is why the owner should not run the unit again until the base has dried. When a cycle stops early or will not start, the technician checks the door latch and the console, since the start signal comes from there. Dishes that come out dirty or wet are traced to the spray arms, the wash pump and the heat-dry element. The owner can safely clear the filter, check that the lower arms spin freely, and confirm the door latches fully before calling.
The model number is printed on the rating label, usually on the edge of the door or the side of the tub, visible when the door is open; match it letter for letter before booking, because a single letter can change parts.
Common issues for this model
- Water left in the tub after the cycle
- Leak or leak-protection code
- Cycle stops early or will not start
- Dishes not getting clean or dry
Related error codes
KitchenAid Dishwasher F3E3 Code: Thermistor/OWI Calibration
F3E3 is a failed thermistor/OWI calibration; the listed causes are an OWI failure or a drain hose check valve letting dirty water back in.
KitchenAid Dishwasher F8E4 Code: Water in Drip Tray or Drain Motor
F8E4 is explained for new installs (connections, float switch, tray, suds); the service tables call it a drain motor electrical fault.
KitchenAid Dishwasher F3E1 Code: Thermistor Circuit Open
F3E1: KitchenAid's service documents call it an open thermistor/OWI sensor circuit. Three causes are listed and no owner fix is given.
KitchenAid Dishwasher Code F10E2 / FAE2: Vent Wax Motor
Some KitchenAid dishwashers only: F10E2 / FAE2 flags the vent wax motor circuit. No owner steps, so service comes next.
Recommended repair service
Dishwasher Repair
Dishwasher not draining, not cleaning, or showing an error code? We find the cause and get your KitchenAid dishwasher back to spotless cycles.
Troubleshooting resources
Note the cycle used, whether water is left in the tub, and any code or flashing light.
Model-information disclaimer. Confirm your exact model number and specifications with your appliance documentation before booking a repair. Model pages are for identification and compatibility reference.
Frequently asked questions
Overall width is 23 7/8 inches, so measure the cabinet opening before ordering a replacement.
Yes. A four-hour delayed start is available from the front console.
Check the rating label on the edge of the door or the side of the tub, visible when the door is open. Copy every letter and digit, including the ones at the end.
Yes. We book in-home visits for this model in the Miami, New York, Houston, Los Angeles and San Diego metro areas. Add the model number and the symptom to the booking form.
Tell us what’s wrong — we’ll take it from there
Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.
Request your repair
Fields marked with * are required.